Motors /- Generators
|
Power- Conditioning
- Inverters
|
Brushless DC- Motor
- Controllers
|
|
Permanent Magnet Generator (PMG) or
Wound Field Generator (WFG)
- High power density
(Power-to-weight ratio).
- PMG uses Neodymium N35 -
80ºC permanent magnets (up to 150ºC available).
- WFG allows field regulation
required for transient loads and synchronous generation.
- Wound Field and Permanent Magnet Rotors
are
interchangeable.
- 3-phase sine waveform - cogging
torque 2% of peak.
- Standard factory insulation
rated at 208VAC (or specify voltage).
- Factory wound for 208VAC at 60Hz
(or specify Volts per RPM).
- Brushless DC Controller
converts a generator into a motor with same power rating.
- Inverter conditions voltage
and frequency from variable speed generator.
145T-PMG in stock - $950.
145T Test
Results click here
|
145T rolled steel
TENV-NEMA frame
|
- 184T cast iron
- TEFC-NEMA frame
|
- Example NEMA frames
- Tedco
Electric => AMEG
We can develop custom frames.
- Performance Information
- (with N35 - 80ºC magnets)
|
-
- 145T Stainless steel
TENV-NEMA frame
|
 - 215T cast aluminum
- TEFC-NEMA frame
|
NEMA
frame
|
Stock
Qty
|
Peak*
W/rpm
|
Continuous
Watts/rpm*
|
Peak Torque
ft-lb
|
Dimensions
Dia. x Len.
|
Weight
lb
|
|
145T
|
15 |
15
|
5 |
100 ft-lb
|
6.5"D x 10"L
|
50 lb
|
|
184T
|
0 |
38
|
12 |
250 ft-lb
|
8.5"D x 12"L
|
100 lb
|
|
215T
|
0 |
67
|
22 |
500 ft-lb
|
10.5"D x 14"L
|
160 lb
|
|
256T
|
0 |
145
|
50 |
1,000 ft-lb
|
12"D x 16"L
|
240 lb
|
|
286T
|
0 |
275
|
100 |
2,000 ft-lb
|
14"D x 20"L
|
385 lb
|
|
326T
|
0 |
400
|
135 |
3,000 ft-lb
|
16"D x 22"L
|
500 lb
|
| 365T
|
0 |
550
|
185 |
4,400 ft-lb
|
18"D x 24"L
|
640 lb
|
| 405T
|
0 |
925
|
310 |
6,600 ft-lb
|
20"D x 28"L
|
860 lb
|
| 445T |
0 |
1670 |
575 |
12,000 ft-lb |
24"D x 32"L |
1,200 lb |
| 506T |
0 |
2360 |
800 |
17,000 ft-lb |
28"D x 38"L |
1,600 lb |
| 588T |
0
|
3580 |
1200 |
25,000 ft-lb
|
30"D x 48"L |
2,200 lb |
* operates at variable speed. kW
varies by torque/current
and RPM. Continuous rating 35% of peak with air-over cooling.
145T rolled steel frame in stock, all
other frames 60 - 90 days pending tooling and/or minimum order.
|
